耐高温沥青胶泥批发价格

耐高温沥青胶泥批发价格

聚氯乙烯胶泥按适温性可分为耐温型和低温型，其中耐温型胶泥耐高温可达85度左右，在通常状态下为黑色弹性固体，表面不粘手，用刀切开可见截面非常细腻，用手按压弹性较好，可快速回弹。反正在手中揉，可粘于手上，有较好的伸长率，可应用于立面伸缩缝，如管道接口密封，污水处理厂立墙伸缩缝密封防水。低温型胶泥为低廉型胶泥，耐高温性较差，夏天温度高时变的非常柔软，没有支撑力，冬天气温变低则变的非常坚硬。但粘结性很好，伸长率一般，一般应用于地平伸缩缝的密封防水，如公路伸缩缝，厂房伸缩缝等。

According to the optimum temperature of PVC. The clay can be divided into high temperature and low temperature, the temperature resistant cement high temperature up to 85 degrees Celsius, normally black elastic solid, the surface is not sticky, cut with a knife visible section is very delicate, pressed by hands, good elasticity, quick rebound. It can be applied to the expansion joint of the facade, such as the sealing of the pipe interface, the sealing of the expansion joint of the vertical wall of the sewage treatment plant, and the waterproof. Low temperature mortar is low type clay, poor heat resistance, summer temperature is very soft, no supporting force, winter temperature becomes low, it becomes very hard. But the adhesion is very good, the elongation is general, generally used in the horizon expansion joint sealing waterproof, such as highway expansion joints, plant expansion joints, etc..

2.聚氯乙烯胶泥产品特点：是以煤焦油为基料，按一定比例加入聚氯乙烯树脂、增塑剂、稳定剂、防老剂及填料、在130-140℃温度下塑化而成的热施工防水接缝材料。聚氯乙烯胶泥具有良好的耐候性，粘结性，弹塑性，耐酸碱腐蚀性，防水可靠，施工方便。

耐高温沥青胶泥批发价格

2. features: PVC cement with coal tar as the base material, is added according to a certain proportion of PVC resin, plasticizer, stabilizer, antioxidant and filler material, waterproof joint thermal construction at the temperature of 130-140 DEG C and the plasticizing. Polyvinyl chloride cement has good weather resistance, cohesiveness, elasticity and plasticity, acid and alkali corrosion resistance, waterproof and reliable, and convenient construction.

3.聚氯乙烯胶泥施工方法：

Construction method of 3. polyvinyl chloride cement:

1）聚氯乙烯胶泥对阵旧水泥混凝土要清除已老化的填缝料及缝内杂物，并保持缝内干燥，含水量应小于6%。

1) polyvinyl chloride cement against old cement concrete to remove aging filler and joint debris, and keep the seam drying, water content should be less than 6%.

（2）新水泥混凝土锯完缝后应清理。

(2) the new cement concrete should be cleaned after sawing.

（3）将聚氯乙烯胶泥成品切成2kg左右的小块投入锅内，缓慢升温，不断搅拌，熔化时温度应控制在120℃，*高温度不超过160℃，保持填缝不起泡，不冒黄烟、浓烟。如发现上述现象，应立即退火，加速搅拌，熔好的填缝料可随时取用并加补新料，连续作业。应避免长时间的加热煎熬，以防填缝料性能发生变化。熔化好的填缝料应立即用壶往缝内浇注，填缝料与路面齐平，多余的料尖用铲刀清除，以保持行车舒适。

耐高温沥青胶泥批发价格

(3) will be cut into about 2kg PVC finished pieces into the pot, slowly heating, stirring constantly, the temperature should be controlled at 120 DEG C melting, the highest temperature does not exceed 160 degrees, keep filling without foaming, do not take tobacco smoke. If the above phenomenon is found, it should be immediately annealed, accelerated mixing, melting filler can be used at any time and add new materials, continuous operation. Long term heating should be avoided to prevent the change of joint properties. The melted filler should be immediately used to sew in the pot pouring sealant, flush with the road surface, the excess material with the shovel tip clearance, to keep driving comfort.

企业名片