CB300*6橡胶止水带报价

橡胶止水带是用来进行止水的;钢边橡胶止水带在橡胶中间焊止水片外面近模板处焊定位片,对于钢边橡胶止水带要求满焊,定位片只要牢固就可以了,定位片距模板要有一到二公分的距离,这之间加塑料或者木质垫片。拆模后剔出,割掉螺杆后用微膨胀砂浆填平。还有种国内少见 就是用短一点的螺杆外加连接螺杆,拆模后可以很方便的拆下。

The rubber sealing strip is used for sealing; steel edged rubber water stop outside the middle rubber waterstop welding near the template at the welding positioning piece, the steel edged rubber water stop full welding requirements, as long as the firm positioning piece can, positioning distance template to one to two cm distance, plastic or wooden pads plus this. After stripping out, cut off after the mortar filled with micro expansion screw. There are kinds of domestic rare connection screw rod is a little shorter, after stripping can be easily disassembled.

橡胶止水带是在混凝土浇注过程中部分或全部浇注埋进混凝土中。在浇埋混凝土以前先要使其在界面部位保持平展，接头部分粘接紧固，再以适当的力充分浇捣，震荡混凝土来定位止水带，使其与混凝土良好的结合，以免影响止水效果。

Rubber sealing strip is partially or wholly poured into concrete in the course of concrete pouring. Before pouring concrete buried first kept flat on the interface at the joint part, adhesive fastening, with appropriate force sufficient to locate the concrete pouring, the shock of waterstop, combining the concrete with good sealing effect, so as not to affect the.

CB300*6橡胶止水带报价

橡胶止水带施工注意事项在施工过程中，由于混凝土中有许多尖角的石和锐利的钢筋，所以在浇捣和定位止水带时，应注意浇捣的冲击力，以免由于力量过大而刺破橡胶止水带。如果发现有破裂现象应及时修补，否则在接缝变形和受水压时橡胶止水带抵抗外力的能力就会大幅度降低。固定止水带时，只能在止水带的允许部位上穿孔打洞，不得损坏本体的部分。在定位橡胶止水带时，一定要使其在界面部

Rubber waterstop construction matters needing attention in the construction process, because there are many sharp corners and sharp stone reinforced concrete, so in the pouring and positioning of the waterstop, should pay attention to the impact of casting, so as to avoid the excess force piercing the rubber sealing belt. If it is found that the rupture phenomenon should be repaired in time, otherwise, in the joint deformation and water pressure, the ability of rubber waterproof belt to resist external force will be greatly reduced. When fixing the water stop belt, the hole can be punched and punched on the allowable part of the water stopping belt, and the part of the body can not be damaged. When locating the rubber stop, make sure it is at the interface

位保持平展，更不能让止水带翻滚、扭结，如发现有扭结不展现象应及时进行调整在浇注固定止水带时，应防止止水带偏移，以免单侧缩短，影响止水效果。在混凝土浇捣时还必须充分震荡，以免止水带和混凝土结合不良而影响止水效果。止水带接头必须粘接良好，如施工现场条件具备，可采用热硫化连接的方法。不加任何处理的所谓“搭接”是**不允许的。

Keep a flat, but can not let the strip rolling and kink, if there is no kink like show should be adjusted in time in the casting and fixing strip, waterstop deviation shall be prevented so as not to affect the sealing effect of unilateral shortened. The concrete must be fully shake when pouring and tamping, so as to avoid the bad combination of the water stop and the concrete and affect the sealing effect. The joint of the water stop belt must be well bonded, such as the condition of the construction site, and the method of heat vulcanization connection. The so-called "lapping" without any treatment is absolutely not allowed.

CB300*6橡胶止水带报价

橡胶止水带施工与安装方法的正确性是使用橡胶止水带的关键所在，我们知道橡胶止水带是在混凝土浇注过程中部分或全部浇埋在混凝土中。由于混凝土中有许多尖角的石子和锐利的钢筋，所以在止水带定位和混凝土浇捣过程中，应注意安装定位方法和浇捣压力，以避免止水带被刺破。由于塑料和橡胶的抗断撕裂强度比拉伸强度低3-5倍，所以如果产品被刺破将会大幅度降低产品抵抗外力的能力，故在施

The correctness of the construction and installation method of rubber water stop belt is the key to use rubber water stop belt. We know that rubber sealing strip is partially or wholly buried in concrete during pouring process. Because there are many sharp stones and sharp steel bars in the concrete, it is necessary to pay attention to installation positioning method and pouring pressure in the process of water stop positioning and concrete pouring and tamping, so as to avoid the sealing belt being punctured. Because the breaking tear strength of plastic and rubber is 3-5 times lower than that of tensile strength, if the product is punctured, it will greatly reduce the ability of the product to resist external force

工中要格外注意。

Pay special attention to the workers.

进行橡胶止水带施工时具体注意如下几个方面：当施工人员在绑扎钢筋和支模时，中埋式橡胶止水带必须采取可靠的固定措施，避免在浇注混凝土时发生位移，保证止水带在混凝土中的正确位置。对于固定橡胶止水带时，只能在止水带的允许部位上穿孔打洞，不得损坏本体部分。对于止水带的固定方法应按设计要求的施工规范进行，常用的固定方法有：利用附加钢筋固定；专用卡具固定；用铅丝和模板固定

The rubber waterstop construction when the specific attention to the following aspects: when the construction personnel in lashing reinforcement and formwork, buried rubber waterstop fixation must take reliable measures to avoid the occurrence of displacement, in the pouring of concrete, to ensure the correct position of waterstop in concrete. For the fixed rubber water stop, holes must be punched on the permitted part of the water stop belt, and the main part shall not be damaged. For the fixed method of waterstop shall be in accordance with the design requirements of the construction specifications, fixation methods are commonly used: the use of additional reinforcement fixation; special fixture fixation; fixation with wire and template

等。不论采用何种固定方法，都必须保证止水带定位准确，不损坏止水带有效部分，方便混凝土浇捣。

Etc.. No matter what kind of fixing method is adopted, it is necessary to ensure the accurate positioning of the water stop belt, not to damage the effective part of the water stop, and to facilitate the pouring and tamping of the concrete.

企业名片